Put a slice of bread in a toaster and it turns golden. Hold it over an open flame and it turns black. Same bread, completely different result. The only thing that changed is how the heat got there.
Heated tobacco works on a similar principle. A small electronic device warms processed tobacco to a controlled temperature that stays below the point of combustion, so the tobacco releases an aerosol without a flame or ash. Three things make that possible: how the stick is built, how the device heats it and how precisely it controls the temperature.
- Heating vs burning: a quick comparison
- What’s inside a heated tobacco stick?
- How does heat turn tobacco into an aerosol?
- What kinds of heating systems do heated tobacco devices use?
- How do heated tobacco devices keep the temperature steady?
- Heated tobacco myths, cleared up
- Heat-not-burn technology, summed up
Let’s take them one at a time.
Heating vs burning: a quick comparison
| Burning tobacco | Heated tobacco | |
|---|---|---|
| How it starts | A flame lights the tip | An electronic heater switches on |
| Temperature | About 700-950°C (1,290-1,740°F) at the tip | About 250-350°C (480-660°F), depending on the device |
| Flame or ember | Yes | No |
| What’s released | Smoke | Aerosol |
| What’s left | Ash and a stub | The used stick, in one piece |
| What controls the heat | The burn itself, plus every draw | Sensors and software in the device |
So what’s the real difference? Control. Combustion is a chemical reaction between tobacco and oxygen that keeps itself going once it starts. A heated device just never lets it start: the electronics hold the temperature below that line for the whole session.
What’s inside a heated tobacco stick?
From the outside, a heated tobacco stick looks like a short cigarette. Inside, it’s built in segments, and each one has a job:
- Tobacco section: the part that sits in the device’s heating zone.
- Support section: holds the tobacco in place and lets the aerosol through.
- Cooling section: brings the temperature of the aerosol down as it travels along the stick.
- Filter: the mouth end.
The tobacco itself is usually reconstituted, which means it’s been ground up and pressed into a thin sheet so it heats evenly. It also contains a humectant such as glycerol, which holds moisture and helps the aerosol form.
Stick design depends on the device, too. Sticks for induction devices, for example, carry a small metal strip that the device heats directly.
How does heat turn tobacco into an aerosol?
Short answer: evaporation, then condensation.
Here’s how it plays out inside the stick:
Heating: the device brings the tobacco up to working temperature.
Evaporation: the water, glycerol and nicotine in the tobacco turn into vapour.
Cooling: the vapour moves along the stick and through the cooling section.
Condensation: the cooled vapour forms tiny droplets suspended in air. That’s the aerosol.
When tobacco burns, most of what comes off it is produced by combustion at far higher temperatures. Heating skips that stage entirely.
Did you know?
You can see the same physics in your kitchen. The cloud above a boiling kettle isn’t steam, because steam is invisible. What you see are tiny water droplets that form when steam meets cooler air.
What kinds of heating systems do heated tobacco devices use?
There are four main types. They differ in where the heat comes from and how it reaches the tobacco.
| Heating system | Where the heat comes from | How it reaches the tobacco |
|---|---|---|
| Blade or pin | A heated blade inside the tobacco | Directly, from the inside out |
| Induction | A magnetic field heating a metal strip in the stick | From within the stick; nothing touches the tobacco |
| External chamber | Heated walls around the stick | Directly, from the outside in |
| Heated airflow | Air warmed inside the device | Warm air passes through the tobacco |
Each comes with a trade-off. Blades collect residue and need regular cleaning. Induction only works with sticks that have a metal strip. An external chamber warms the outer tobacco first. Airflow systems depend on a steady stream of warm air.
Ploom is one example of the airflow approach. Its HEATFLOW technology, used in the PLOOM AURA device, is designed to keep the temperature steady through a five-minute session. The first heat-up takes about 25 seconds, or 30 seconds in its intensive mode.
How do heated tobacco devices keep the temperature steady?
Sensors and a small processor check the heat constantly and adjust the power, so the tobacco stays in its working range from start to finish. You’ll mostly notice this through a few simple things:
→ Heat-up time. A short warm-up before a light or vibration tells you the device is ready.
→ Timed sessions. A session ends on its own after a set time or number of draws.
→ Heating modes. Some devices let you pick a mode or adjust intensity in an app. This changes how the device heats, not what’s in the stick.
→ Battery limits. Devices cap how many sessions can run back to back.
Tip!
If heating feels uneven or a session cuts out early, the usual suspects are a heating chamber that needs cleaning or a battery that isn’t fully charged. Check the manufacturer’s cleaning and charging instructions first.
Heated tobacco myths, cleared up
Myth: Heated tobacco is just another e-cigarette.
✓ Fact: An e-cigarette heats a liquid. Heated tobacco heats processed tobacco leaf. Both contain nicotine, and both are regulated products.
Myth: The tobacco is still lit, just at a lower temperature.
✓ Fact: There’s no flame or ember at any point. The heater keeps the tobacco below its ignition point from the first second to the last.
Myth: Heated tobacco sticks are regular cigarettes with a heater added.
✓ Fact: They’re designed to be heated by a device, not lit.
Myth: Heated tobacco has no nicotine.
✓ Fact: The sticks contain tobacco, and tobacco naturally contains nicotine, which is addictive.
Heat-not-burn technology, summed up
Heated tobacco is warmed electronically and kept below the point where it would burn, so it releases an aerosol instead.
The stick is built in segments that hold the tobacco, then cool the aerosol on its way out.
Devices use one of four heating systems, and what separates them is where the heat comes from.
